Kamis, 21 Oktober 2010

ccna lab 7

Lab 7.2.5 Configuring a Wireless Access Point
Objective
• Configure the wireless access point (AP) portion of a multi-function device to allow access to a
wireless client. Background / Preparation The Linksys WRT300N includes an integrated 4-port switch, a router and a wireless Access Point (AP). In this lab, you will configure the AP component of the multi-function device to allow access for wireless clients. The basic wireless capabilities of the multi-function device will be configured but this will not be a secure wireless network. Setting up a secure wireless network will be covered in a later lab.
The following resources are required:
• Windows XP based computer that is cabled to the multi-function device
• Linksys WRT300N
Step 1: Verify connectivity between the computer and the multi-function device
a. The computer used to configure the AP should be attached to one of the multi-function device’s
switch ports.
b. On the computer, click the Start button and select Run. Type cmd and click OK or press Enter.
c. At the command prompt, ping the multi-function device using the default IP address 192.168.1.1 or the IP that has been configured on the multi-function device’s port. Do not proceed until the ping succeeds.
d. Write down the command used to ping the multi-function device.
Jawaban = jika dilakukan test ping dengan command ping 192.168.1.1 maka yang akan muncul ialah request time out. Hal ini dikarenakan IP pada AP telah dikonfigurasi ulang. Maka dengan setinggan otomatis DHCP ip address yang diberikan ialah 192.168.180.148 maka akan muncul replay from.
NOTE: If the ping is not successful, try these troubleshooting steps:
• Check to make sure the IP address of the computer is on the 192.168.1.0 network. The computer
must be on the same network as the multi-function device to be able to ping it. The DHCP service of the multi-function device is enabled by default. If the computer is configured as a DHCP client it should have a valid IP address and subnet mask. If the computer has a static IP address, it must be in on the 192.168.1.0 network and the subnet mask must be 255.255.255.0.
• Make sure the cable is a known-good straight-through cable. Test to verify.
• Verify that the link light for the port where the computer is attached is lit.
• Check whether the multi-function device has power.
If none of these steps correct the problem, check with your instructor.
Step 2: Log in to the multi-function device and configure the wireless network
a. Open a web browser. In the address line, type http://ip_address, where ip_address is the IP address of the wireless router (default is 192.168.1.1). At the prompt, leave the user name textbox empty, but type the password assigned to the router. The default password is admin. Click OK.
b. In the main menu, click on the Wireless option.
c. In the Basic Wireless Settings window, the Network Mode shows mixed by default, because the AP supports 802.11b, g, and n wireless devices. You can use any of these standards to connect to the AP. If the wireless portion of the multi-function device is NOT being used, the network mode would be set to Disabled. Leave the default of Mixed selected.
d. Delete the default SSID (linksys) in the Network Name (SSID) textbox. Enter a new SSID using your
last name or name chosen by your instructor. SSIDs are case-sensitive.
e. Write down the exact SSID name that you are using.?
Jawaban= aditya
f. Click on the Radio Band drop-down menu and write down the two options?setelah di konfigurasi ternyata dapat terkoneksi akan tetapi setinggan tidak dapat diubah pada default bawaan packet tracer, sehingga tidak ada pilihan pada network mode dan radio band.
g. For a wireless network that can use 802.11b, g, or n client devices, the default is Auto. Auto allows the Wide Channel option to be chosen and gives the best performance. The Standard Channel option is used if the wireless client devices are 802.11b or g, or both b and g. The Wide Channel option is used if only 802.11n client devices are being used. Leave the default of Auto selected.
h. SSID Broadcast is set to enabled by default, which enables the AP to periodically send out the SSID using the wireless antenna. Any wireless devices in the area can detect this broadcast. This is how clients detect nearby wireless networks.
i. Click on the Save Settings button. When the settings have been successfully saved, click on Continue.
j. The AP is now configured for a wireless network with the name (SSID) that you gave it. It is important
to write down this information before starting the next lab or attaching any wireless NICs to the wireless network.
Step 3: Reflection
a. How many wireless networks do you think could be configured in one classroom? What would limit
this?
Jawaban = dalam satu classroom pada wireless di access point ternyata batas nya diberikan 50 user. Jadi ip address yang bisa dikonfigurasikan sebanyak 50 client seperti 192.168.1.100-192.168.1.149
b. What do you see as a potential security problem when you broadcast your SSID from the AP?
Jawaban = jika settingan SSID pada access point disetting default maka akan memudahkan bagi attack wlan untuk menyerang system wireless yang digunakan untuk berbagai keperluan.
Lab 7.2.6 Configuring a Wireless Client
Objective
• Install and configure a driver for a wireless USB NIC for a wireless client computer.
• Determine the version of the driver installed and check the Internet for updates.
Jawaban = manufacture nya ialah = intel cooperation
Product name = B6A14TRQ
Background / Preparation
In this lab you will install a driver for a wireless USB NIC in a computer. The driver is a type of software that controls the wireless NIC. The driver comes on a CD with the NIC or can be downloaded from the Internet. Many manufacturers require that the driver is installed before the adapter is connected. The procedure described in this lab is for a Linksys USB 802.11g wireless NIC, but is similar to others. You should always follow the procedure recommended by the wireless NIC manufacturer.
The following resources are required:
• Windows XP-based computer with an available USB port
• Wireless USB NIC and associated driver
• Administrator rights to install the driver
• Linksys WRT300N with wireless access configured from previous lab
Step 1: Install the wireless NIC driver
a. Insert the CD that contains the wireless NIC driver into the CD/DVD drive and install the driver according to the manufacturer recommendations. Most USB devices require that the driver be installed before the device is physically attached. Note that you may do part of the installation process now and part of it after the wireless NIC is installed.
b. Who is the manufacturer of the wireless NIC? LINKSYS
c. Describe how you installed the wireless NIC driver. ?setelah dimasukkan CD driver product wireless dilakukan pengkonfigurasian pada alat access point dengan cara membuka browser dan masukan alamat bawaan product lalu akan muncul interface untuk pengaturan jaringan. Pengaturan yang dilakukan ialah mengubah nama default setting dan memberikan konfigurasi IP address perlu juga dilakukan pengkonfigurasian pada batasan minimum dan maksimum client. Dan yang terpenting ialah pengaturan security agar mencegah serangan dari luar. Adapun langkah-langkah nya:
1. masukkan CD installer product (pada kasus ini Linksys)
2. buka web browser, lalu masukkan alamat IP default pada browser.
3. akan muncul GUI product lalu lakukan pengaturan pada set up.
- pilih automatic DHCP
-lalu berikan batasan IP address dan subnet mask yang diizinkan.
-enabled kan dhcp server
4. setelah itu lakukan pengaturan pada wireless
-ubah nama SSID default menjadi nama yang kita hendaki.
-pilih jenis network mode
-lalu enabled kan SSID broadcast.
Step 2: Install the wireless NIC
a. When prompted, connect the USB NIC cable to an available USB port. Click Next to continue.
Step 3: Attach to the wireless network
a. Most wireless NIC adapters have client software to control the NIC. The software shows any wireless networks that are discovered. Select the SSID of the wireless network that you configured on the AP in a previous lab.
b. Which SSID are you using?pada settingan ini digunakan aditya
c. If the wireless NIC did not connect to the wireless network, perform the appropriate troubleshooting.
d. What is the signal strength for the wireless NIC?elektronika 1
e. Did the wireless NIC see any other wireless networks in the area?yes
Why or why not? Karena pada computer terdapat network adapter dan pada sinyal wireless yang terdeteksi telah di enabled kan untuk dapat dikoneksikan.
f. Show your active wireless connection to a fellow student or the lab assistant.
g. What is another name for a wireless host?
-elektronika2
-elektronika1
-elektronika unp
-elo_1 test
h. Is it better to use the client software from the wireless NIC manufacturer or let Windows XP control
the wireless NIC? Lebih bagus menggunakan client software.
Step 4: Determine the NIC driver version
a. Hardware manufacturers continually update drivers. The driver that ships with a NIC or other piece of hardware is frequently not the most current.
b. To check the driver version for the NIC you installed, click Start, select Control Panel and then
Network Connections. Right-click on the wireless connection and select Properties. Click the Configure button for the NIC and then the Driver tab. What is the name and version of the driver you
installed? Realtek RTL8187B Wireless 802.11b/g 54 Mbps USB 2.0 network adapter.

Step 5: Determine if the NIC driver is the most current
a. Search the NIC manufacturer web site for drivers that support the wireless NIC you installed. Are
there more current ones available?
- 1394 Net Adapter
- Marvel Yukon 88E8040T PCI-E Fast Ethernet Controller
- Realtek RTL8187B Wireless 802.11b/g 54 Mbps USB 2.0 Network Adapter

b. What is the most current one listed? Realtek RTL8187B Wireless 802.11b/g 54 Mbps USB 2.0 Network Adapter
c. If there is a more current driver, how would you apply it? Jika pada computer cukup dengan menambahkan port NIC baru sehingga bisa menambahkan Driver lebih. Atau jika pada laptop cukup menambahkan slot PCI.
Step 6: Verify connectivity
a. Once you have installed the NIC, it is time to verify connectivity with the Linksys WRT300N.
b. Open a web browser such as Windows Internet Explorer or Mozilla Firefox.
c. In the address line type http://192.168.1.1, which is the default setting on the AP.
d. In the Connect to 192.168.1.1 dialog box, leave the username text box empty, and type admin in the password text box. Leave the Remember my password checkbox unchecked. Click OK.
e. If you receive the Linksys Setup screen, you have established connectivity with the AP. If you do not establish connectivity, you will have to troubleshoot the connection by checking to ensure the devices are turned on and the IP addresses on all devices are correct. Which IP address should be configured on the wireless NIC? Jika terkendala dengan masalah koneksi maka yang harus diperhatikan ialah pengaturan pada SET UP dan di tetapkan kembali IP address dan menetukan batas maksimum dan minimum pada IP client.
Step 7: Reflection
a. Do you think the process of setting up a wireless network at a food store or book store is any different from what you just did?pengaturannya sama.Why or why not? Karena perangkat yang digunakan untuk menginstall wireless masih sama dan proses penginstalan juga tidak terlalu berbeda. Dan karena wireless pada tempat makan atau took buku masih skop kecil sehingga pengaturan masih sama.
b. Do you think the AP model that you are using would be sufficient for the food store in your
neighborhood? Why or why not? Bisa menggunakan PSK (pre-shared key) karena access point hanya bisa di berikan kepada pelanggan toko tersebut dengan memberikan kunci atau password hanya kepada pelanggan.

Lab 7.3.5 Configuring Wireless Security
Objectives
• Create a security plan for a home network.
• Configure the wireless access point (AP) portion of a multi-function device using security best practices.
Background / Preparation
A well-planned security implementation is critical to the safety of a wireless network. This lab goes over the steps that must be taken to ensure the safety of the network using the following scenario. You have just purchased a Linksys WRT300N wireless router, and you want to set up a small network in your home. You selected this router because the IEEE 802.11n specification claims that it has 12 times the speed of an 802.11g and 4 times the range. Because the 802.11n uses 2.4 GHz, it is backward compatible with both the 802.11b and 802.11g and uses MIMO (multiple-in, multiple-out) technology. You should enable security mechanisms before connecting your multi-function device to the Internet or any wired network. You should also change the default values provided, because they are well-known values that are easily obtainable on the Internet.
The following resources are required:
• Windows-based computer
• Linksys WRT300N
• Straight-through Ethernet cable
Step 1: Plan the security for your home network
a. List at least six security best practices that you should implement to secure your multi-function device
and wireless network.
1) Kurangi kekuatan pancar antena WAP
2) Berikan security code
3) Aktifkan MAC address filter.
4) Ganti Password default
5) Disable Broadcast SSID
6) Disable DHCP Server
b. Describe what the security risk is for each item.
1) kelemahan atau resikonya misalnya disebuah tempat usaha atau perusahaan maka semakin jauh titik akses dari akses point mengakibatkan kecepatan akses sangat terpengaruh atau bahkan tidak menjanjikan sama sekali.
2) bagi orang yang tidak paham teknologi akan kebingungan dalam memberikan security code.
3) jika seandainya MAC address seseorang client pernah diblokir pada suatu tempat, akan tetapi belum dibuka kembali maka tidak bisa digunakan pada tempat akses lain.
4) jika password pada default diganti, akan susah mengetahui paswor yang baru jika tidak dikonfirmasikan terhadap teknisi.
5) jika tidak diaktifkan kembali, maka titik access tidak dapat diditeksi oleh wireless adapter.
6)jika di disabledkan maka hanya IP address yang telah diregisterkan yang bisa mengakses jaringan, sehingga jaringan tidak bersifat bebas layaknya wi-fi zone pada umumnya.
Step 2: Connect a computer to the multi-function device and log in to the web-based utility
a. Connect your computer (Ethernet NIC) to the multi-function device (port 1 on the Linksys WRT300N) by using a straight-through cable.
b. The default IP address of the Linksys WRT300N is 192.168.1.1, and the default subnet mask is 255.255.255.0. The computer and Linksys device must be on the same network to communicate with each other. Change the IP address of the computer to 192.168.1.2, and verify that the subnet mask is 255.255.255.0. Enter the internal address of the Linksys device (192.168.1.1) as the default gateway. Do this by clicking, Start > Control Panel > Network Connections. Right click on the wireless connection and choose Properties. Select the Internet Protocol (TCP/IP) and enter the addresses as shown below.
c. Open a web browser, such as Internet Explorer, Netscape, or Firefox and enter the default IP address of the Linksys device (192.168.1.1) into the address field and press Enter.
d. A screen appears, requesting your user name and password.
b. Leave the User name field blank and enter admin for the password. It is the default password on the Linksys device. Click OK. Remember that passwords are case-sensitive.
c. As you make the necessary changes on the Linksys device, click Save Settings on each screen to save the changes or click Cancel Changes to keep the default settings.

Step 4: Change the Linksys device password
a. The initial screen displayed is the Setup > Basic Setup screen.
b. Click the Administration tab. The Management tab is selected by default.
c. Type in a new password for the Linksys device, and then confirm the password. The new password must not be more than 32 characters and must not include any spaces. The password is required to access the Linksys device web-based utility and Setup Wizard.
d. The Web Utility Access via Wireless option is enabled by default. You may want to disable this
feature to further increase security.
e. Click the Save Settings button to save the information.
NOTE: If you forget your password, you can reset the Linksys device to the factory defaults by pressing the RESET button for 5 seconds and then releasing it. The default password is admin.
Step 5: Configure the wireless security settings
a. Click the Wireless tab. The Basic Wireless Settings tab is selected by default. The Network Name is the SSID shared among all devices on your network. It must be identical for all devices in the wireless network. It is case-sensitive and must not be more than 32 characters.
b. Change the SSID from the default of linksys to a unique name. Record the name you have chosen:
jawaban
aditya
c. Leave the Radio Band set to Auto. This allows your network to use all 802.11n, g, and b devices.
d. For SSID Broadcast, select the Disabled button to disable the SSID broadcast. Wireless clients
survey the area for networks to associate with and will detect the SSID broadcast sent by the Linksys
device. For added security, do not broadcast the SSID.
e. Save your settings before going to the next screen.
Step 6: Configure encryption and authentication
a. Choose the Wireless Security tab on the Wireless screen.
b. This router supports four types of security mode settings:
• WEP (Wired Equivalent Privacy)
• WPA (Wi-Fi Protected Access) Personal, which uses a pre-shared key (PSK)
• WPA Enterprise, which uses Remote Access Dial In User Service (RADIUS)
• RADIUS CCNA Discovery
c. Select WPA Personal Security Mode.
d. On the next screen, choose an Encryption algorithm.
To secure a network, use the highest level of encryption possible within the Selected Security mode. The following Security Modes and Encryption levels are listed from least secure (WEP) to most
secure (WPA2 with AES)
• WEP
• WPA
o TKIP (Temporal Key Integrity Protocol)
o AES (Advanced Encryption System)
• WPA2
o TKIP
o AES
AES is only supported by newer devices that contain a co-processor. To ensure compatibility with all devices, select TKIP.
e. For authentication, enter a pre-shared key between 8 and 63 characters. This key is shared by the Linksys device and all connected devices.
f. Choose a key renewal period between 600 and 7200 seconds. The renewal period is how often the Linksys device changes the encryption key.
g. Save your settings before exiting the screen.
Step 7: Configure MAC address filtering
a. Choose the Wireless MAC Filter tab on the Wireless screen.
b. MAC address filtering allows only selected wireless client MAC addresses to have access to your network. Select the radio button to Permit PCs listed below to access the wireless network. Click the Wireless Client List button to display a list of all wireless client computers on your network.

c. The next screen allows you to identify which MAC addresses can have access to the wireless network. Click the Save to MAC Address Filter List check box for any client device you want to add, and then click the Add button. Any wireless clients, other than those in the list will be prevented from accessing your wireless network. Save your settings before exiting the screen.
Step 8: Reflection
a. Which feature that you configured on the Linksys WRT300N makes you feel the most secure and
why?
Jawaban = aplikasi atau program yang membuat saya merasa lebih aman dan nyaman ketika mengkonfigurasi ialah MAC address filtering. Alasannya karena pada aplikasi ini terdapat sebuah pilihan untuk memberikan izin access kepada client yang telah terlebih dahulu alamat IP dan MAC address nya dicantumkan atau didaftarkan.
b. Make a list of other items that could be done to make your network even more secure.
Pada pengaturan wireless kita pilih wireless security dan security modenya kita ganti dari disabled menjadi WEP sehingga dapat memberikan kunci berlapis. Atau pada system operasi windows biasa kita aktifkn juga menu firewall dan kita aktifkan juga menu SYS.

Rabu, 20 Oktober 2010

ccna lab 6

Lab 6.2.1 Observing DNS Name Resolution
Objectives
• Observe the conversion of a URL to an IP address.
• Observe DNS lookup using the nslookup command.
Background / Preparation
Domain Name System (DNS) is invoked when you type a Uniform Resource Locator (URL), such as http://www.cisco.com, into a web browser. The first part of the URL describes which protocol is being used. Common ones are HTTP (Hypertext Transfer Protocol), HTTPS (Hypertext Transfer Protocol over Secure Socket Layer), and FTP (File Transfer Protocol). DNS uses the second part of the URL, which in this example is www.cisco.com. DNS translates the domain name (like www.cisco.com) to an IP address in order to allow the source host to reach the destination host.
Work in pairs to complete this lab.
The following resources are required:
• Windows-based computer with Internet connectivity
• Access to the Run command
Step 1: Observe DNS conversion
a. Click the Start button, select Run, type cmd, and then click OK. The command prompt window appears.
b. At the command prompt, type ping www.cisco.com. The computer needs to translate www.cisco.com into an IP address so it knows where to send the Internet Control Message Protocol (ICMP) packets. Ping is a type of ICMP packet.
c. The first line of the output shows www.cisco.com converted to an IP address by DNS. You should be able to see the effect of DNS even if your school has a firewall that prevents pinging, or if Cisco has prevented people from pinging their web server.
d. Which IP address is shown on the screen? IP address yang ditampilkan ialah 60.254.168.170
e. Is it the same as the one shown in the figure?yes.Why do you think this occurred? Hal ini terjadi karena CISCO memiliki system DNS sehingga alamat cisco meskipun diakses dari computer yang berbeda alamat IP akan tetapi alamat DNS pada CISCO telah teregritasi pada alamat khusus di internet.
f. Work together with another student and discuss one or two other instances (besides the ping command) in which the computer would use DNS. Selain ping perintah lain pada kokmputer yang menggunakan DNS ialah nslookup
Step 2: Verify DNS operation using the nslookup command
a. At the command prompt, type the nslookup command.
b. What is the default DNS server being used?www.unp.ac.id
c. Notice how the command prompt changed. This is the NSLOOKUP prompt. From this prompt, you can enter commands related to DNS.
d. At the prompt, type ? to see a list of all the available commands that you can use in NSLOOKUP mode.
e. Write three commands that you can use with NSLOOKUP= contoh tiga perintah yang bisa digunakan pada nslookup adalah:
1. set type=all
nslookup dengan set type=all. bertujuan untuk melihat name server pada suatu domain.
2. set type=mx
nslookup dengan set type=mx. Bertujuan untuk mengetahui Mail eXchangernya.
3. set type=soa
nslookup dengan set type=soa. Bertujuan untuk mengetahui Start Of Authority nya.
f. At the NSLOOKUP prompt, type www.cisco.com.
g. What is the translated IP address? 60.254.168.170
h. Is it the same as the IP address shown with the ping command?sama.
i. At the prompt, type the IP address of the Cisco web server that you just found. You can use NSLOOKUP to get the domain name of an IP address if you do not know the URL. Using the previous procedures, find an IP address associated with www.google.com.
Ip address yang terkait dengan google ialah : 64.233.181.103, 64.233.181.104, 64.23.181.105, 64.233.181.99 , 64.233.181.147 dan 64.233.181.99
Step 3: Identify mail servers using the nslookup command
a. At the prompt, type set type=mx to have NSLOOKUP identify mail servers.
b. At the prompt, type www.cisco.com.
c. What is the primary name server, the responsible mail address, and the default Time to Live (TTL)?
Nama server : e144.cd.akaiemdge.net
Address : 60.254.168.170
Aliases : www.cisco.com, www.cisco.com.akands.net
d. At the prompt, type exit to return to the regular command prompt.
e. At the prompt, type ipconfig /all.
f. Write the IP addresses of all the DNS servers that your school uses?. 10.1.1.3
g. Type exit to close the command prompt window. CCNA Discovery
Step 4: Reflection
a. If your school did not have a DNS server, what effect would this have on your use of the Internet? Jika tidak memiliki alamat DNS maka situs internet pada sekolah kita maka situs sekolah itu dianggap tidak terdaftar karena tidak teregistrasi.
b. Some companies do not dedicate a single server for DNS. Instead, the DNS server provides other functions as well. Which functions do you think might be included on a DNS server? Use the ipconfig /all command to help you with this.
Lab 6.2.3 Exploring FTP
Objective
• Demonstrate how to use FTP from the command prompt and GUI. Background / Preparation File Transfer Protocol (FTP) is part of the TCP/IP suite. FTP is used to transfer files from one network device to another network device. Windows includes an FTP application that you can execute from the command prompt. There are also many free GUI versions of FTP that you can download. The GUI versions are easier to use than typing from a command prompt. When using FTP, one computer is normally the server and the other computer is the client. When accessing the server from the client, you need to provide a username and password. Some FTP servers have a userID named anonymous. You can access these types of sites by simply typing “anonymous” for the userID, without a password. Usually, the site administrator has files that can be copied but does not allow files to be posted with the anonymous userID. If your class does not have an FTP server available, you can download and install a freeware version, such as Home FTP Server or Cerberus FTP server. The FTP Server on a computer running the CCNA Discovery Live CD may also be used. Another computer will act as the FTP client by using FTP from the command line, a web browser, or download a freeware version of an FTP client, such as SmartFTP Client or Core FTP LE client. Work in teams of two to complete this lab.
The following resources are required:
• Windows-based computer with an FTP client
• FTP server (Existing FTP server, downloaded freeware, or use Live CD)
Step 1: Examine FTP from the command prompt
a. Click the Start button, select Run, type cmd on the command line, and then click OK.
b. At the prompt, type ftp to start the FTP application. The prompt changes.
c. From the ftp prompt, type ? to see a list of the commands that can be used in this mode.
d. List three FTP commands.
ls Mendaftar berkas-berkas
cd Mengganti direktori
bin Menentukan mode transfer biner
e. At the prompt, type help put to see a short description of the put command.
f. What is the purpose of the put command?
g. Use the help command again to get the purpose of the get, send, and recv commands.
get pada ftp server digunakan untuk mendownload berkas
send Mengirim file yang berada dalam komputer lokal ke komputer server yang sedang di-remote
recv Mengcopy file yang ada di remote computer ke dalam computer local
NOTE: The original FTP commands were PUT to send a file to an FTP server and GET to download a file from the FTP server. You also had to select ASCII or binary file mode. If you download a binary file in ASCII mode it could end up being corrupted. Some of the newer graphical programs now use send and receive in their place.
h. Partner with another student. Using procedures demonstrated in previous labs, write down the names and IP addresses of each partner computer. It is very important to get these names correct. Some
FTP applications allow you to use either the IP address or the computer name.
Computer 1: __________________________________________________________________
Computer 2: __________________________________________________________________
Step 2: Use a GUI FTP client or web browser
a. If you are using a web browser as the FTP client, open the web browser and type ftp://ip_address_of_FTP_server. If the FTP server is configured to use an anonymous userID, connect directly to the FTP server. Using the FTP client, download an available file from the server.
b. If you are using a GUI FTP client, open the application. For most FTP clients, you must configure a
new connection by giving it a name, the IP address of the FTP server, and a username and password. You may have to type anonymous if the FTP server allows this type of connection. Some applications have a checkbox that allows an anonymous login. When you have configured the connection, connect to the FTP server and download a file.
c. What is the name of the file you downloaded from the FTP server? ______________________
d. List one example of when FTP might be beneficial to a computer technician. _______________
____________________________________________________________________________
____________________________________________________________________________
Step 3: (Optional) Use both an FTP server and client
a. If you control both the FTP server and client, practice sending files to and getting files from the client
and the server.
b. Show your transferred files to another group of students.
c. Close the FTP server and client applications.
Lab 6.2.4 Configuring an Email Client
Objectives
• Set up an email client.
• Send and receive mail from a mail server.
• Add an email account or change an existing one.
Background / Preparation
An email application gives the user the ability to send and receive messages from another user located on the same local network or on the Internet. The messages are sent by the sending client and stored on an email server. Another email client with a mailbox on the server can then access the server at any time to receive stored messages that are destined for that client.
The following resources are required:
• Windows-based computer with Internet connectivity
• Microsoft Outlook or other email client software
Step 1: Open Microsoft Outlook
a. From the Start menu, select All Programs. Locate the Microsoft Office software.
b. Select Microsoft Office Outlook as the email program. If your computer does not have the Microsoft Office software, there are many free email software packages available on the Internet. Search the Internet to find a free email client that can be installed on your computer. The following instructions may vary depending on your email client.
Step 2: Set up an email account
a. When you first start Microsoft Outlook, a screen appears with Email Upgrade Options. You can choose to import email messages or address books from another account. Because this is your first email account, select the Do Not Upgrade button.
b. The next screen is the Email Accounts screen where you are asked if you want to configure an email account. Click Yes.
c. If Outlook has already been installed and setup for e-mail previously, you can start the Outlook application and click Tools, E-Mail Accounts and then select View or change existing e-mail account to see how the existing account is set up.


Step 3: Enter POP3 e-mail account information
a. The next screen requires the user of the new account to fill in information. Enter your name and email address. Your can get your email address from your Internet provider.
NOTE: If you do not have a real ISP email account, this step can be treated as a simulation. Just enter the information requested to become familiar with the process of creating an email account.
b. Enter your server information. Contact your Internet provider to locate the server information for the
incoming and outgoing mail servers. Usually Internet providers put this information on their website in
their help section.
c. What is your incoming (POP3) mail server? POP3 (Mail server)
d. What is your outgoing (SMTP) mail server? (SMTP) mail server
e. Enter your username and password. Do not check the box to remember your password. This option is used when only one person uses the computer. If anyone else were to use the computer, they could easily gain access to all of the information in your email.
f. Click the Test Account Settings button. If everything is correct, the screen displays that the test was
successful. If not, correct your information and try again. NOTE: If this is a simulation, the test will not be successful and you can go to Steps 4 and 5.
g. Test your new account by sending an email to a friend in class.
Step 4: (Optional) Add another account or change an account
a. Open Microsoft Outlook. From the Tools menu, select Email Accounts.
b. In this screen, you can add another email account or you can change information in an existing account.
Step 5: Reflection
a. What are the advantages or disadvantages to using email over regular postal mail? Keuntungan dengan akun yang mudah dibuat dan gratis. Info dari mail server bisa delink kan dengan smartphone. Sedangkan kerugian kapasitas atau kuota email terbatas, banyak pesan yang dianggap spam.
b. What are the advantages or disadvantages to using email over an instant messaging program?
Keuntungannya koneksi atau komunikasi terjadi secara langsung, kerugiannya aplikasi yang diberikan masih minim.
c. With a partner, discuss five (5) recommendaions for email etiquette that should be considered when
emailing friends and business colleagues.
1. Jangan melakukan SPAM.
2. Hapuslah pesan reply yang tidak perlu.
3. Bersabarlah dalam menunggu "reply".
4. Benahi susunan email "forwards" anda
5. Gantilah "Subject" atau judul email bila topik pembicaraan anda berubah.

Rabu, 13 Oktober 2010

jawaban tugas CCNA 1.6

1. A user types www.cisco.com into a web browser address textbox. What does www.cisco.com represent?(the IP address of a web server)

2. What type of server would use IMAP? (e-mail)

3. Which type of server would most likely be used first by a network client in a corporate environment? (DHCP)

4. Which protocol is used by FTP to transfer files over the Internet? (TCP)

5. Which protocols are TCP/IP application layer protocols? (Choose two.)
(a.FTP b.SMTP)

6. Which of the following are layers of the TCP/IP model? (Choose three.)
(a. Application b.Internet c. Network Access )

7. You are creating a network-based video game. What influences your decision about which transport protocol to use for the application?
(UDP will not disrupt the game to retransmit dropped packets.)

8. Whenever e-mail clients send letters, what device is used to translate the domain names into their associated IP addresses? (DNS server )

9. Which application is most likely used to translate www.cisco.com to 198.133.219.25? (FTP)

10. Refer to the graphic. Which protocol is used to access this website? (bonus)

11. Which port number is used by SMTP? (20)

12. Which protocol is used by e-mail servers to communicate with each other?(SMTP )

13. What client software enables logged in users to communicate with other logged in users in real time? (instant messaging)

14. An Internet server is running both FTP and HTTP services. How does the server know which of these applications should handle an incoming segment? (The packet header identifies it as an HTTP or FTP packet. )

15. What term is used to describe how TCP/IP protocols are layered and interact to format, address, and transmit information across a network? (protocol layering )

16. What three items are contained in an Ethernet frame? (Choose three.)
a.destination MAC address b. source MAC address c. source IP address

17. What information is contained in an IP header? (source and destination IP addresses )

18. Cabling issues are associated with which OSI layer? (1)

19. A device receives an Ethernet frame and recognizes the MAC address as its own. What does the device do to the message to get to the encapsulated data?
( removes the Ethernet header and trailer )
20. A client has decoded a frame and started the de-encapsulation process. In which order does the de-encapsulation process occur?
1) remove IP header
2) remove Ethernet header and trailer
3) remove TCP header
4) pass data to the application


21. What is an advantage of the use of layers in the OSI reference model?
(It prevents changes in one layer from affecting other layers. )

22. What is the correct order of the layers of the OSI reference model, starting at the lowest layer and working up the model? (physical, data link, network, transport, session, presentation, application )

CCNA lab 5



TUGAS
CCNA LAB ACTIVITY 5

Unp

DISUSUN OLEH :
Aditya Mafa’id
2008/00683

PENDIDIKAN TEKNIK INFORMATIKA
FAKULTAS TEKNIK
UNIVERSITAS NEGERI PADANG
2010


Background / Preparation
Network technicians work with binary, decimal, hexadecimal numbers with computers and networking devices. In this lab you will use the Windows Calculator application to convert between the binary, decimal, and hexadecimal number systems. You will also use the powers function to determine the number of hosts that can be addressed based on the number of bits available. 
The following resources are required:
•  PC with Windows XP installed and functional
Step 1: Access Windows Calculator and determine mode of operation
a.  From the Start button menu, select All Programs > Accessories, and click on Calculator. An
alternate method of starting the Calculator application is to access the Start menu, click on Run, type
calc and press Enter. Try both methods.
b.  Once the Calculator application opens, select the View menu option.
c.  Which mode [Standard | Scientific] is currently active? Mode yang aktif ialah model kalkulator standar.
d.  Select the Standard mode. This is a basic mode for simple calculations. How many mathematical
functions are available in this mode?fungsi matematika yang terdapat pada kalkulator standar hanya ada 7 fungsi
e.  From the View menu option, select the Scientific Calculator mode.



f.  How many mathematical functions are available in this mode? Model operasi matematika pada kalkulator  Scientific ada 33 fungsi jika telah aktif semua
Step 2: Convert between number systems
a. Access Scientific mode. Notice the number system modes available—Hex (Hexadecimal), Dec
(Decimal), Oct (Octal), and Bin (Binary).
b.  Which number system is currently active?  Number system yang aktif pada Scientific mode pada awal pertama dijalankan ialah Dec yang artinya Desimal.
c.  Which numbers on the number pad are active in Decimal mode? Pada mode decimal seluruh angka dari 0-9 aktif.
Click on the Bin (Binary) mode radio button. Which numbers on the number pad are now active? Pada mode Binary angka yang aktif hanya  0 dan 1
d.  Why do you think the other numbers are grayed out?  Karena pada pengoperasian bilangan binary angka yang dikenal hanya 1 dan 0. Pada binary angka yang bisa dioperasikan hanya 1 dan 0.
e.  Click on the Hex (Hexadecimal) mode radio button. 
f.  Which characters on the number pad are now activated?  Jika menggunakan mode hexadecimal pada pad number ditamabah dengan aktifnya komponen huruf A, B, C, D, E, F.
g.  Click on the Dec radio button. Using your mouse, click on the number 1 followed by the number 5 on
the number pad. The decimal number 15 has now been entered. Click on the Bin radio button. 
h.  What happened to the number 15 listed in the textbox at the top of the window? Ketika diganti ke mode Bin angka 15 berubah menjadi 1111
i.  By selecting different modes, numbers are converted from one number system to another. Select Dec
mode again. The number in the window converts back to decimal. Select the Hex mode.
j.  Which hexadecimal character (0 through 9 or A through F) represents decimal 15? Ketika angka 15 dikonvresikan ke hexadecimal yang muncul ialah F.
k.  Clear the number 15 in the window.  Select Dec mode again. Not only can the mouse be used to  enter numbers, but the numerical keypad on the keyboard as well as numbers on the keyboard can  also be used. Using the numerical keypad to the right of the ENTER key, type the number 22. Note  that if the number does not enter into the calculator, press the Num Lock key to enable the numeric  keypad. While the number 22 is showing in the calculator, use the number keys across the top of the  keyboard to add a 0 to the number 22 (220 should now be on the calculator). Select the Bin radio button.
l.  What is the binary equivalent of 220? Hasil konversi decimal 220 ke Binary menghasilkan  11011100
m.  Clear the number 220 in the window.  From Binary mode, type in the following binary number:
11001100. Select the Dec radio button.
n.  What is the decimal equivalent to the binary number of 11011100? Hasil konversi bilangan Bin 11011100 pada decimal ialah 220
o.  Convert the following decimal numbers to binary.
DECIMAL
BINARY
86
1010110
175
10101111
204
11001100
19
10011

p.  Convert the following binary numbers to decimal.
BINARY
DECIMAL
11000011
195
101010
42
111000
56
10010011
147

Step 3: Convert host IP addresses
a.  Computer hosts usually have two addresses, an Internet Protocol (IP) address and an Ethernet  Media Access Control (MAC) address. For the benefit of humans, the IP address is normally represented as a dotted decimal notation, such as 135.15.227.68. Each of the decimal octets in the  address or a mask can be converted to 8 binary bits. Remember that the computer only understands  binary bits. If all 4 octets were converted to binary, how many bits would there be?karena masing-masing octet  terdiri dari 8 bit jika diterjemahkan akan terdapat 32 bit
b.  IP addresses are normally shown with four decimal numbers ranging from 0 to 255 and separated by  a period. Convert the 4 parts of the IP address 192.168.10.2 to binary. 
Decimal
Binary
192
11000000
168
10101000
10
1010
2
10
c.  Notice in the previous problem how the 10 converted to only four digits and the number 2 converted
to only two digits. When IP addresses can have any number from 0 to 255 in each position, eight  digits are normally used to represent each number. In the previous example, eight digits were needed  to convert 192 and 168 to binary, but 10 and 2 did not need as many digits. Normally 0s are added to  the left of the digits to have eight digits in binary for each IP address number. The number 10 would  be shown as 00001010. Four extra zeros are added to the front of the other four binary digits.
d.  On the calculator in Binary mode, enter the digits 00001010 and select the Dec radio button.
e.  Which decimal number is equivalent to 00001010?   Setelah dikonfersikan kebilangan desimal hasilnya 10
f.  Did adding “leading” zeros affect the number any? Tidak, angka nol didepan tidak berpengaruh.
g.  What would the number 2 (in the previous example) be if you were to make it eight digits? 00000010
itu hasilnya jika dikonversi kedalam 8 bilangan bit.
Step 4: Convert host IP subnet masks
  1. Subnet masks, such as 255.255.255.0, are also represented as dotted decimal. A subnet mask will  always consist of four 8-bit octets, each one represented as a decimal number. With the exception of  decimal 0 (all 8 binary zeros) and decimal 255 (all 8 binary ones), each octet will have some number of ones on the left and some number of zeros on the right. Convert the 8 possible decimal subnet octet values to binary. 


decimal
binary
0
00000000
128
10000000
192
11000000
224
11100000
240
11110000
248
11111000
25
       11111100

                                   254
                               11111110

255
11111111
  1. Convert the four parts of the subnet mask 255.255.255.0 to binary. 
Decimal
BInary
255
11111111
255
11111111
255
11111111
0
00000000
Step 5: Convert broadcast addresses
a.  Computer hosts and network devices use broadcast addresses to send messages to all hosts.
Convert the following broadcast addresses.
Address
Binary
IP broadcast
255.255.255.255
11111111. 11111111. 11111111. 11111111
MAC broadcast
FF:FF:FF:FF:FF:FF
11111111. 11111111. 11111111. 11111111. 11111111.     11111111



Step 6: Convert IP and MAC addresses for a host
a.       Click the Start button, select Run, type cmd, and press Enter. From the command prompt, type ipconfig /all.
  1. Make a note of the IP address and physical address (also known as a MAC address).
IP Address:
MAC Address:
  1. Using the calculator, convert the four numbers contained in the IP address to binary.
Ip addressnya ialah 192.168.194.189
Decimal
Binary
192
11000000
168
10101000
194
11000010
189
10111101
  1.  The MAC or physical address is normally represented as 12 hexadecimal characters, grouped in pairs and separated by dashes (-). Physical addresses on a Windows-based computer are shown in a format of xx-xx-xx-xx-xx-xx, where each x is a number from 0 to 9 or a letter from a to f. Each of the hex characters in the address can be converted to 4 binary bits which is what the computer understands. If all 12 hex characters were converted to binary, how many bits would there be?  Akan ada 96 biner yang terbentuk
  2.  Convert each of the hexadecimal pairs to binary. For example, if the number CC-12-DE-4A-BD-88-34 was the physical address, convert the hexadecimal number CC to binary (11001100). Then convert the hexadecimal number 12 to binary (00010010) and so on. Be sure to add the leading zeros for a total of 8 binary digits per pair of hex digits.
Hexadecimal
binary
00
0
16
10110
44
1000100
F5
11110101
F2
11110010
52
1010010

Step 7: Manipulate powers of 2 to determine the number of hosts on a network 
a.  Binary numbers use two digits, 0 and 1. When you calculate how many hosts can be on a subnetwork, you use powers of two because binary is being used. As an example, we have a subnet mask that leaves six bits in the host portion of the IP address. In this case, the number of hosts on that network is 2 to the 6th power minus 2 (because you need a number to represent the network and a number that can be used to reach all the hosts—the broadcast address). The number 2 is always used because we are working in binary. The number 6 is the number of bits that are used for the host bits.
b.  On the calculator, in Dec mode, input the number 2. Select the x^y key, the key which raises a number to a power. Input the number 6. Click on the = key, press Enter on the keyboard, or press the= key on the keyboard—all give the total. The number 64 appears in the output. To subtract two, click on the minus (-) key and then the 2 key followed by the = key. The number 62 appears in the output. This means 62 hosts could be utilized.
c.  Using the previously described process, determine the number of hosts if the following number of bits are used for host bits.
No. of Bits Used for
Hosts
No. of Hosts 
5
30 hosts
14
16382 hosts
24
16777214 host
10
1022 hosts
  1. Using a similar technique as learned previously, determine what 10 to the 4th power equals.
Maka diperoleh 9998
  1. Close the Windows Calculator application.

Step 8: (Optional) Determine the network number and number of hosts based on subnet mask
a.  Given the IP network address of 172.16.203.56 and a subnet mask of 255.255.248.0, determine the network portion of the address and calculate how many hosts can be created from host bits left.
b.  Start by converting the 4 octets of the decimal IP address to binary and then convert the decimal subnet mask to binary. Remember to include leading zeros when converting to binary in order to make a total of 8 bits per octet. 
Decimal IP address
and subnet mask
Binary IP address and subnet mask
172.16.203.56
10101100.00010000.11001011.00111000
255.255.248.0
11111111.11111111.11111000.00000000
  1. Align the 32 bits of the subnet mask to the 32 bits of the IP address and compare them. The bits in the IP address that align with the ones bits in the subnet mask represent the network number. What is the binary and decimal network number for this IP address? Determine the binary address first (include all 32 bits) and then convert it to decimal. 
Binary network address:
10101100.00010000.11001011.00111000
11111111.11111111.11111000.00000000

10101100.00010000.11001000.00000000

Decimal network address:
172.16.200.0

  1. How many ones bits are in the subnet mask? Banyak bit di subnet mask = 2n = 23=8
e.        How many bits are left for host bits? Host = 2n-2= 25-2= 30

  1. How many hosts can be created with the bits left? Host =2n-2= 211-2= 2046

Step 9: Reflection
  1. List one other thing for which you might use the Windows Calculator scientific mode. It does not have to be related to networking.
Fungsi dari kalkulator bawaan microsoft bukan hanya sebagai alat operasi hitung dasar. aplikasi ini dapat digunakan untuk mengkonversi nilai dari satu satuan ke satuan yang lain.